我安装panabit 后运行，但是不能能进入管理页面

7336059ok

panabit# /y/bin/ipectrl start
kldload: can't load /y/kernel/if_em.ko: File exists
Warning: fail to load optimized em driver
Please recompile your kernel without em enabled!
Otherwise, you can't get the maximum performance
of panaos provides!
kern.jos.ipe_netdevices: rl1 rl2  -> rl1 rl2
net.inet.tcp.msl: 2000 -> 2000
panaos is running!
network is started!
Starting ipe_httpd ......
bind: No such file or directory
bind: Address already in use
/y/bin/ipe_httpd: can't bind to any address
ipe_httpd is started!
ipe_monitor is started!
data monitor is started!

为什么不能进入管理页面呢？请高手指点

netstorms

Starting ipe_httpd ......
bind: No such file or directory
bind: Address already in use
/y/bin/ipe_httpd: can't bind to any address

httpd需要用的端口被其他服务占用了？

7336059ok

panabit# /usr/panabit/bin/ipectrl start
kldload: can't load /usr/panabit/kernel/if_em.ko: File exists
Warning: fail to load optimized em driver
Please recompile your kernel without em enabled!
Otherwise, you can't get the maximum performance
of panaos provides!
kern.jos.ipe_netdevices: rl1 rl2 -> rl1 rl2
net.inet.tcp.msl: 2000 -> 2000
Load module "mmap" ......
Load module "pci" ......
        rl1@bus0:9:0: 0x10ec:0x8139
        rl2@bus0:10:0: 0x10ec:0x8139
Load module "cmds" ......
Load module "dma" ......
This is standard version, no PANAOS DMA supported!
Load module "mgmt" ......
Load module "mbuf" ......
        jos_mbuf_minit: 64 mbuf allocated
Load module "intf" ......
Load module "em" ......
JOSEM not installed!
Load module "bsd" ......
        interface rl1 attached, mac address 00:19:E0:21:2D:B5
        bring interface rl1 up
        interface rl2 attached, mac address 00:E0:4C:8B:28:A8
        bring interface rl2 up
network is started!
Starting ipe_httpd ......
ipe_httpd is started!
ipe_monitor is started!
/usr/panabit/bin/ipe_httpd: started as root without requesting chroot(), warning only
data monitor is started!
panabit# Load module "ipe" ......
Load module "watcher" ......
Load module "tbucket" ......
Load module "key" ......
Load module "keytable" ......
Load module "flow" ......
        flow size 64, entry size 32
Load module "node" ......
        table size 131072, pool size 131072,node size 32
Load module "xping" ......
Load module "port" ......
port module initialzied, max port 65536
Load module "protocol" ......
Load module "localip" ......
Load module "policy" ......
Load module "license" ......
Load module "thread" ......
Load module "xping" ......
Load module "flow" ......
        share CPU with control plane!
panaos startup!
loading configuration .....
begin to start thread xping ...
begin to start thread flow ...
flow(0x827f400) start executing...
Loading configurations into kernel ......
kern.jos.ipe_policyid: 0 -> 0
kern.jos.ipe_planid: 0 -> 0
configuration loaded!

为何这样还是不行方问管理页面呢